Get Latest [Sep-2021] Conduct effective penetration tests using UpdateDumps NACE-CIP1-001
Penetration testers simulate NACE-CIP1-001 exam PDF
NEW QUESTION 14
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. High Relative Humidity
- B. Low Surface Temperature
- C. Low Relative Humidity
- D. High Surface Temperature
Answer: C
NEW QUESTION 15
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 45 Gauge readings resulting in 15 Spot Measurements
- B. 225 Gauge Readings resulting in 75 Spot Measurements
- C. 105 Gauge Readings resulting in 35 Spot Measurements
- D. 75 Gauge Readings resulting in 25 Spot Measurements
Answer: B
NEW QUESTION 16
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 80% of the specified minimum thickness
- B. 100% of the specified maximum thickness
- C. 90% of the specified maximum thickness
- D. 70% of the specified maximum thickness
Answer: A
NEW QUESTION 17
Which of these tests uses a syringe?
- A. Sleeve test
- B. Bresle patch
- C. Potassium ferricyanide
- D. Soluble salts meter
Answer: B
NEW QUESTION 18
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Synthetic oil or grease may not be identified
- B. Presence of weld spatter may produce a false positive
- C. Chloride salt may produce a false positive
- D. Ultra-Violet light may contaminant the surface
Answer: A
NEW QUESTION 19
The Inspector should record the serial numbers of inspection instruments:
- A. Only when verifying accuracy of the instrument
- B. Only if the instrument is suspected of not working properly
- C. Only if the specification requires it
- D. Each time the instrument is used
Answer: D
NEW QUESTION 20
Corrosion generally occurs at which of the following sites:
- A. Electrolyte
- B. Anode
- C. Metallic pathway
- D. Cathode
Answer: B
NEW QUESTION 21
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. Pass/fail criteria
- B. A final conflict resolution method
- C. A method to grade surface profile
- D. A general guide
Answer: D
NEW QUESTION 22
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Carefully review the document and do the best you can
- B. Advise the owners' representative of your lack of knowledge in this area
- C. Hire a third patty to assist you in understanding the document
- D. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
Answer: A
NEW QUESTION 23
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
Answer: A
NEW QUESTION 24
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Rust Grades A-D
- B. Rust Grades 1-4
- C. Surface Condition H
- D. Surface Conditions E-G
Answer: A
NEW QUESTION 25
Non Conformance Reports are completed by the Inspector:
- A. In accordance with the specification's definition of a non-conformance
- B. In every instance that an item does not meet the specification requirements
- C. When the Inspector deems it to be a significant non-conforming item
- D. When the Inspector and Contractor deem it to be a significant non-conforming item
Answer: D
NEW QUESTION 26
The Inspector's Log Book is generally:
- A. Retained by the inspector upon project completion
- B. Submitted to the client upon project completion
- C. Shared with all parties upon project completion
- D. Shredded by the inspector upon project completion
Answer: A
NEW QUESTION 27
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Record the segment with the more aggressive profile
- B. Record the segment with the less aggressive profile
- C. Use another method as the comparator method is too subjective
- D. Record your result by identifying two segments
Answer: B
NEW QUESTION 28
Relative humidity is
- A. the highest temperature at which moisture forms on a steel surface.
- B. a measure of the amount of moisture in the air compared to saturation level.
- C. a measure of the amount of moisture in the air compared to the air temperature.
- D. the lowest temperature at which moisture forms on a steel surface.
Answer: B
NEW QUESTION 29
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing
- A. scratches the surface too deeply resulting in uneven coating application
- B. develops a good anchor profile resulting in uneven coating application.
- C. develops a polished surface, which is a poor anchor profile for most coatings
- D. damages structural elements thereby speeding up the corrosion process.
Answer: C
NEW QUESTION 30
What is used to determine compressed air cleanliness?
- A. Profilometer
- B. Psychrometer
- C. Needle pressure gauge
- D. Blotter test
Answer: A
NEW QUESTION 31
......
Tested Material Used To NACE-CIP1-001 Test Engine: https://www.updatedumps.com/NACE/NACE-CIP1-001-updated-exam-dumps.html
Steps Necessary To Pass The NACE-CIP1-001 Exam: https://drive.google.com/open?id=1un4Rath2xvsQDYASn7qclec4MzS1_Vu-