The Best Practice Test Preparation for the 300-510 Certification Exam
300-510 Exam Dumps, Practice Test Questions BUNDLE PACK
How to study the Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) Exam
For the Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) Exam, Cisco offers several options on their website. Cisco provides classroom training through which Cisco's authorized learning partners teach instructor-led classes all over the world. E-Learning solutions are provided by Cisco for exam preparation via self-paced online courses. Students are highly encouraged to join Cisco's Certification community where they can join students from all over the world and learn together. After taking all the official training courses, 300-510 SPRI practice exams are a must to get a proper understanding of exam format and question types. For further exam self-study materials, refer to the links down below:
We recommend a combination of hands-on experience, completion of the training course, and self-study in the areas described in the Exam Outline section of this exam guide as preparation for this exam.
Hover on to Cisco's Website and complete the official training course provided for the exam. Check for the topics mentioned in the Exam Outline section of this guide to review the online documentation, tip sheets, and user guides and study the details relevant to those topics. Refer to the links at the end of this document for more study material.
Topics of Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) Exam
These core topics of 310-510 SPRI practice test listed below are general recommendations for the material that is likely to be used for the examination. However, on any delivery of the test, other similar topics could also appear. The guidelines below can update at any time without notice to better represent the contents of the 310-510 SPRI exam dumps pdf and for clarity purposes.
It is recommended that, where possible, the applicant use these courses and/or other resources to provide background information on the exam objectives. The syllabus for the Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) examination is listed below in detail for each section of 300-510 SPRI exam dumps:
- Implement Multiarea IS-IS
- Enable and Optimize PIM-SM
- Implement PIM-SM Enhancements
- Describing Segment Routing Traffic Engineering (SR-TE)
- Describe how traffic engineering is used in segment routing networks
- Influencing Border Gateway Protocol Route Selection
- Implementing Interdomain IP Multicast
- Implement and verify MPLS
- Implement mechanisms for dynamic Rendezvous Point (RP) distribution
- Implement Multicast Source Discovery Protocol (MSDP) in the interdomain environment
- Implementing and Verifying Open Shortest Path First Multiarea Networks
- Improving BGP Convergence and Implementing Advanced Operations
- Implementing Route Redistribution
- Implementing IP Multicast Concepts and Technologies
- Implement BGP Route Reflectors
- Implement advanced features to improve convergence in BGP networks
- Configure and Verify Interior Gateway Protocol (IGP) Segment Routing
- Implement and verify segment routing technology within an interior gateway protocol
- Implementing PIM-SM Enhancements
- Implementing PIM-SM Protocol
- Implement enhanced Protocol-Independent Multicast - Sparse Mode (PIM-SM) features
- Securing BGP in Service Provider Networks
- Implement Route Redistribution
- Implementing Segment Routing
- Implementing Cisco MPLS Traffic Engineering
- Implement BGP security options
- Implement Cisco MPLS TE
- Troubleshooting Routing Protocols
- Troubleshoot Routing Protocols
- Implementing and Verifying Intermediate System to Intermediate System Multilevel Networks
- Deploying IPv6 Tunneling Mechanisms
- Implementing Distributed Rendezvous Point Solution in Multicast Network
- Implement BGP Security Options
- Implement and troubleshoot MPLS traffic engineering
- Influence BGP Route Selection
- Implement OSPF Special Area Types (IPv4 and IPv6)
- Implement MPLS in the Service Provider Core
- Introducing Routing Protocol Tools, Route Maps, and Routing Policy Language
NEW QUESTION 88
Refer to the exhibit.
Refer to the exhibit The branch office in area 10 is connected to HQ via Frame Relay uplinks with bandwidth constraints After a recent implementation of QoS on the R2 and R3 networks the system has been logging %SYS-2-MALLOCFAIL: Memory allocation of 65536 bytes failed from 0x224E321, alignment 0 messages To reduce traffic load and memory utilization on R2 and R3 the network engineer configured R1 to announce only one user subnet per location by issuing the summary address 192.168.0.0 255.255.248.0 command en R1 However, the engineer noticed that router R2 still has two routes and a summary address from HQ and R3 also has two routes from HQ Which two actions must the engineer take on R1 to fix the issue so that only one route is announced' (Choose two.)
- A. Configure RI as a Level 1 device.
- B. Configure a summary route for Level 1-Level 2 devices.
- C. Configure the subnet range with the network command under the IS-IS process.
- D. Redistribute both routes into the ISIS process.
- E. Configure a summary route for Level 1 devices.
Answer: B,E
NEW QUESTION 89
Refer to the exhibit. A network operator is working to filter routes from being advertised that are covered under an aggregate announcement.
The receiving router of the aggregate announcement block is still getting some of the more specific routes plus the aggregate.
Which configuration change ensures that only the aggregate is announced now and in the future if other networks are to be added?
- A. Configure the summary-only keyword on the aggregate command
- B. Set each specific route in the AGGRO policy to drop instead of suppress-route
- C. Set each specific route in the AGGRO policy to remove instead of suppress-route
- D. Filter the routes on the receiving router
Answer: A
NEW QUESTION 90
Which cost is the default when redistributing routes from BGP to OSPF?
- A. 0
- B. 1
- C. infinite
- D. automatic
Answer: A
Explanation:
Explanation/Reference: http://www.ciscopress.com/articles/article.asp?p=27573
NEW QUESTION 91
Drag and drop the attributes for the BGP route selection on the left into the correct order on the right. Not all options are used.
Answer:
Explanation:
NEW QUESTION 92
Refer to me exhibit. A network engineer sets up a multihoming eBGP topology where multiple Autonomous Systems connect to ASN 64501.
The engineer wants to block all the routers coming from ASN 64502. but allow all the others. For that purpose, the following AS Pam prefix 1st s being used:
(config)#ip as-path access-list 10 deny _64502$
What must be fixed to achieve this result?
- A. The statement must CM modified with ip as path access list 1 deny A64502$
- B. The AS-PATH filter must be defined inside the route-map mode
- C. At the end ip as-path access-list 10 permit .* must be included
- D. The statement must be modified with ip as-path access-list 1 deny _64502_
Answer: C
NEW QUESTION 93
Refer to the exhibit.
A network operator is getting the route for 10.11.11 0/24 from two upstream providers on
#XR3. The network operator must configure #XR3 to force the 10.11.11.0/24 prefix to route via next hop of 10.0.0.9 as primary when available. Which of these can the operator use the routing policy language for, to enforce this traffic forwarding path?
- A. weight of 100 on the prefix coming from 192.168.0.1
- B. weight of 0 on the prefix coming from 192.168.0.2
- C. higher local preference on the prefix coming from 192.168.0.1
- D. lower local preference on the prefix coming from 192.168.0.2
Answer: B
NEW QUESTION 94
Refer to the exhibit.
An engineer has configured all routers in the environment to run IS-IS Level 1 and Level 2 routing. The engineer wants traffic from R1 to R5 to pass via R2. but IS-IS routing has calculated the best path via R4. Which action corrects the problem?
- A. Set the link metric on R2 for the links from router R2 to routers R3 and R4 to 30 or more.
- B. Configure routers R1, R4, and R5 for Level 2 routing only.
- C. Set the link metric for the link from router R1 to router R4 to 30 or more.
- D. Configure routers R1, R2, and R5 for Level 1 routing only.
Answer: C
NEW QUESTION 95
Refer to the exhibit.
Which attribute can router 1 alter so that only other iBGP peers prefer to use 192.168.4.2 as the next hop for route 192.168.3.0/24?
- A. weight
- B. origin
- C. MED
- D. local preference
Answer: C
NEW QUESTION 96
Refer to the exhibit.
P1 and PE3 Cisco IOS XR routers are directly connected and have this configuration applied. The BGP session is not coming up. Assume that there is no IP reachability problem and both routers can open tcp port 179 to each other. Which two actions fix the issue? (Choose two.)
- A. Change MD5 to HMAC-MD5
- B. Change MD5 to HMAC-ESP
- C. Change MD5 to SHA-1
- D. Change MD5 to HMAC-SHA1-12
- E. Remove the send and accept lifetime under key 1
Answer: A,D
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/routers/crs/software/crs_r4-0/security/configuration/guide/ sc40crsbook_chapter5.html
NEW QUESTION 97
Refer to the exhibit.
Which statement about this configuration is true?
- A. Router 1 receives up to two paths from neighbor 192.168.1.1 for all routes in the same AS
- B. Router 1 sends and receives multiple best paths from neighbor 192.168.1.1
- C. Router 1 receives only the best path from neighbor 192.168.1.1
- D. Router 1 sends up to two paths to neighbor 192.168.1.1 for all routes
Answer: B
NEW QUESTION 98
Refer to the exhibit.
An engineer working for a private telecommunication company with an employee id 3977 74 814 implemented the configuration on Router 1. what is the effect of it?
- A. Router 1 receives only one best path from neighbor 192.168.1.1
- B. Router 1 sends only one best path to neighbor 192 168.1.1.
- C. Router 1 sends and receives multiple best paths from neighbor 192.168.1.1
- D. Router 1 sends up to three paths to neighbor 192.168.1.1 for all routes
Answer: C
NEW QUESTION 99
Refer to the exhibit.
Answer:
Explanation:
Solution:
R1
Router bgp 100
Neigh 10.3.3.3 remote-as 100
Neigh 10.3.3.3 update-source loopback0
Address-family ipv4
Neigh 10.3.3.3 next-hop-self
Aggregate-address 172.16.100.0 255.255.252.0 summary-only
Copy run start
R3
Router bgp 100
Neigh 10.1.1.1 remote-as 100
Neigh 10.1.1.1 update-source loopback 0
Copy run start
Verification:-
NEW QUESTION 100
Refer to the exhibit.
CE1 and CE2 cannot communicate through the service provider BGP peering is established between PE1 and PE2. IS-IS is the only routing protocol running in the service provider core. What step can be done to troubleshoot the issue?
- A. Switch the IGPs running in the core from IS-IS to OSPF to support a Cisco MPLS TE tunnel from PE1 to PE2.
- B. Configure BGP between CE and PE routers.
- C. Verify the MPLS LSPs.
- D. Confirm that IS-IS is running with metric-style narrow.
Answer: D
NEW QUESTION 101
Refer to the exhibit.
Why is neighbor 10.1.5.5 stuck in "2WAY" state?
- A. It is an expected behavior when OSPF network type is broadcast
- B. Router ID 10.1.5.5 is not reachable from R2
- C. OSPF authentication has failed between R2 and 10.1.5.5
- D. OSPF parameters (Area ID or hello interval) are mismatched between R2 and 10.1.5.5
Answer: A
NEW QUESTION 102
Refer to the exhibit.
After troubleshooting BGP traffic steering issue, which action did the network operator take to achieve the correct effect of this configuration?
- A. Routes that have originated through AS 65517 have the local preference set to 150.
- B. Routes that have passed through AS 65517 have the local preference set to 150.
- C. Routes that have passed through AS 65517 have the local preference set to 150 and the traffic is denied.
- D. Routes directly attached to AS 65517 have the local preference set to 150.
Answer: B
NEW QUESTION 103
Refer to the exhibit.
An engineer has successfully fixed BGP peering issue. R1 has an established eBGP peering with R2 and R3. Which mechanism should the engineer apply in order to steer the traffic correctly?
- A. The MED attribute can be applied on R2 to influence R1 to use it as the primary path.
- B. The IGP metric can be manipulated on R1 to allow traffic to be load balanced between R2 and R3.
- C. The local preference attribute can be applied on R3 to influence AS 65513 to use AS 65515 as the secondary path.
- D. The weight attribute can be applied on R2 to influence AS 65513 to use AS 65515 as the primary path.
Answer: B
NEW QUESTION 104
......
More about 300-510 Exam
If you target the CCNP Service Provider, the Cisco 300-510 test comes second after 350-501 exam, normally called the core validation. 300-510 test, on the other hand, is among two other concentration tests, namely, the Cisco 300-515 and 300-535. To add more, 300-510 exam is into topics like routing protocols, MPLS, segment routing, and policy language. The duration set aside for it is 1.5 hours and the amount to pay during registration is $300. Sadly, Cisco does not give any report regarding the least score that takers of this test should get for the sake of becoming certified. So, striving for high marks should be your aim. However, in case your attempt is not successful the first time, there is a chance to redo the test once five days have elapsed from the date you attempted it.
The best audience for exam 300-510 include network administrators, network designers, project managers, and system engineers, among other specialists.
Prepare for the Actual CCNP Service Provider 300-510 Exam Practice Materials Collection: https://www.updatedumps.com/Cisco/300-510-updated-exam-dumps.html
CCNP Service Provider Certification 300-510 Sample Questions Reliable: https://drive.google.com/open?id=1wX-M41jJKY-Hmuz1jElNDesrBmlAUrjA