[May 22, 2023] 300-615 PDF Questions and Testing Engine With 169 Questions
Updated Exam Engine for 300-615 Exam Free Demo & 365 Day Updates
The Cisco 300-615 exam, also known as Troubleshooting Cisco Data Center Infrastructure, is designed to test the skills and knowledge of IT professionals who work with Cisco data center infrastructure. This exam is part of the CCNP Data Center certification track and is intended for individuals who have experience troubleshooting complex data center infrastructure issues. The exam covers a range of topics, including troubleshooting routing protocols, virtualization, storage, and network security.
NEW QUESTION # 35
Drag and drop the commands from the left onto the correct categories on the right.
Answer:
Explanation:
NEW QUESTION # 36
Refer to the exhibit.
A network engineer is implementing a pair of Cisco Nexus 9000 Series Switches. During the OSPF configuration, the engineer discovers unstable routing in the network. The investigation shows flapping routes after the new switches were introduced. Which set of actions resolves the issue?
- A. Configure a new IP address on the Ethernet interface toward the OSPF neighbor. Clear the OSPF process.
- B. Configure a new IP address on the Ethernet interface toward the OSPF neighbor. Clear the OSPF neighbor.
- C. Configure a new OSPF priority on the Ethernet interface toward the OSPF neighbor. Clear the OSPF neighbor.
- D. Configure a new IP address on the Loopback interface for the OSPF process. Clear the OSPF process
Answer: B
NEW QUESTION # 37
An engineer is troubleshooting a custom AV pair that was created by a client on an external authentication server to map a read-only role for a specific security domain. Which AV pair solves the problem?
- A. shell=Security_Domain_1/Read_Role_1|Read_Role_2
- B. shell:domains=Security_Domain_1/Read_Role_1|Read_Role_2
- C. shell:domains=Security_Domain_1/Write_Role_1|Read_Role_2
- D. shell:domains=Security_Domain_1//Read_Role_1|Read_Role_2
Answer: B
NEW QUESTION # 38
Drag and drop the commands from the left onto the correct categories on the right.
Answer:
Explanation:
NEW QUESTION # 39
An engineer is troubleshooting issues in Cisco UCS Director. Drag and drop the possible causes from the left onto the correct issues on the right.
Answer:
Explanation:
NEW QUESTION # 40
Refer to the exhibit.
Refer to the exhibit. A network engineer must use BGP to route IPv4 and IPv6 routes between R1 and R2. The IPv4 addresses are exchanged as expected between the routers through BGP. The routers have reached an Established BGP state. However, the IPv6 routes from R2 fail to show in the routing table of R1. Which action resolves the issue?
- A. Advertise L2VPN EVPN under IPv4 unicast address family
- B. Enable IPv6 routing on R1
- C. Configure an IPv6 BGP neighbor on R1
- D. Create a route map that sets the IPv6 next hop.
Answer: D
NEW QUESTION # 41
Refer to the exhibit.
Refer to the exhibit. One of the vPC VTEPs fails to route VXLAN traffic to vPC connected hosts. When the issue was being diagnosed, it was discovered that the packets that were expected to be forwarded to the MAC address on the SWITCH-VTEP-1 are instead forwarded to the MAC address on SWITCH-VTEP-2 and then dropped. Which action resolves the issue?
- A. Configure a distributed anycast gateway on both peers
- B. Configure peer-gateway under the VPC domain on both peers
- C. Configure ip arp synchronize under the VPC domain on both peers
- D. Configure a different secondary IP address for one of the vPC peers
Answer: B
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/command/reference/vpc/n5k-vpc-cr/n5k-vpc_cmds_i.html#:~:text=a%20port%20profile.-,ip%20arp%20synchronize,no%20form%20of%20this%20command.
NEW QUESTION # 42
Refer to the exhibit.
The initiator that has FC ID 0x970102 fails to communicate with the target that has FC ID 0x970200. What action resolves the issue?
- A. Reset the port for FC ID 0x970209 and FC ID 0x9700c2 to log in to the fabric.
- B. Reconfigure the initiator and the target to be in the same zones.
- C. Reactivate the zoneset.
- D. Reset the port for FC ID 0x970102 and FC ID 0x970200 to log in to the fabric.
Answer: B
NEW QUESTION # 43
Refer to the exhibit.
A Postman call to a Cisco APIC fails. The access credentials were confirmed to be configured as expected.
Which action resolves the issue?
- A. Modify the protocol to HTTP
- B. Change operation type to POST
- C. Change the IP address to a domain name
- D. Modify the target protocol type to XML
Answer: B
NEW QUESTION # 44
Refer to the exhibit.
The connection between a Cisco Nexus 5548UP switch and a Cisco MDS switch fails to initialize. What is the cause of the issue?
- A. The interface is in an incorrect mode.
- B. The SFP is unsupported.
- C. VSAN 1 is suspended.
- D. Trunk mode must be activated.
Answer: C
NEW QUESTION # 45
Refer to the exhibit.
A network engineer needs to capture traffic from the VMs that utilize the IOM host interface Eth1/1/23 of a Cisco UCS B-Series chassis. A traffic analyzer is used to get traffic captured from the Eth1/4 interface of the subordinate fabric interconnect. The network engineer notices that traffic is not captured on the traffic analyzer. Which action resolves the issue?
- A. Span the traffic from the Eth 1/2 of the subordinate fabric interconnect.
- B. Span the traffic from the Eth 1/4 of the primary fabric interconnect.
- C. Span the traffic from the Eth 1/2 of the primary fabric interconnect.
- D. Span the traffic from the Eth 1/4 of the subordinate fabric interconnect.
Answer: B
NEW QUESTION # 46
Refer to the exhibit.
The script fails to bring up Ethernet 1/2 when Ethernet 1/1 goes down. Which change enables the script to run as intended?
- A. Set the port VLAN
- B. Configure an enable action
- C. Include an action to manually shut down Ethernet 1/1
- D. Add an action to configure the terminal
Answer: D
NEW QUESTION # 47
Refer to the exhibit. A blade that is connected to FI-A fails to boot from a SAN LUN. The boot policy is configured to boot by using vHBA0 as the SAN Primary. Which action resolves the issue?
- A. Set VSAN to 11 in vHBA_SAN_
- B. Change vHBA0 to VSAN 11 in Service Profile
- C. Change Adapter Policy to VMWare on vHBA0
- D. Configure vHBA_SAN_A zone to VSAN 10
Answer: D
NEW QUESTION # 48
Refer to the exhibit.
The scheduler was configured to save the running-config automatically daily. However, the scheduler is returning the error presented. Which action resolves the issue?
- A. Use the kstack attribute for copying the configuration file
- B. Change the file transfer protocol to TFTP in scheduler job
- C. Reconfigure the scheduler using the admin user
- D. Remove vrf management from the command
Answer: D
NEW QUESTION # 49
Drag and drop the commands from the left onto the correct categories on the right.
Answer:
Explanation:
NEW QUESTION # 50 
Refer to the exhibit. A network engineer is configuring the FCoE N_Port virtualization storage area network.
After the initial implementation, server 11 fails to connect to the disk array. Which action resolves the issue?
- A. On N9K interface vfc11, change switchport mode configuration to NP
- B. On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to F
- C. On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to E
- D. On MDS interface vfc 1/1, change switchport mode configuration to VF
Answer: C
NEW QUESTION # 51
During a boot process of a Cisco UCS C-Series Rack Server, an engineer receives a "No Signal" message from the vKVM and physical connection. Which set of steps resolves the issue?
- A. 1- Disconnect the power cord
2- Confirm that all cards are property seated
3- Connect the power cord and power on the server - B. 1- Disconnect the power cord
2- Confirm that all cards are properly seated
3- Connect the power cord - C. 1- Power off the server and disconnect the power cord
2- Confirm that all cards are available
3- Connect the power cord and power on the server - D. 1- Power off the server and disconnect the power cord
2- Confirm that all cards are property seated
3- Connect the power cord and power on the server
Answer: D
Explanation:
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/ts/guide/b_C-Series_Troubleshooting_Guide.pdf
NEW QUESTION # 52
Refer to the exhibit.
When an engineer inserts 8-Gb FC SFP port 15 on a Cisco UCS Fabric Interconnect, the port fails. What is a possible cause of the issue?
- A. The polarity of the fiber cable is reversed.
- B. Port 15 is configured as an Ethernet port.
- C. Port 15 is configured for 4-Gb FC.
- D. Port 15 is missing a license.
Answer: B
NEW QUESTION # 53
A user reports that they cannot reach from a UCS server to an FC Storage array. Which command is used to test communication between an FCF and a target?
- A. traceroute
- B. fcping
- C. ping
- D. fcroute
Answer: B
NEW QUESTION # 54 
Refer to the exhibit. A PC belongs to VLAN 68. The user experiences a large amount of packet loss when communicating with hosts that are outside of VLAN 68. Which action resolves the problem?
- A. Configure ip arp synchronization on both switches.
- B. Enable the peer-gateway feature.
- C. Remove the HSRP configuration.
- D. Replace HSRP with GLBP.
Answer: B
Explanation:
Section: Network
Explanation
Explanation/Reference: https://community.cisco.com/t5/networking-documents/peer-gateway-feature-on-the-nexus-7000/ ta-p/3113290
NEW QUESTION # 55
Refer to the exhibit.
The EEM script fails to send an SNMP trap when a user attempts to enter configuration mode. Which configuration is missing from the script?
- A. policy-default action statement
- B. event-default action statement
- C. IP address of the SNMP server
- D. event statement
Answer: C
NEW QUESTION # 56
Refer to the exhibit.
A network engineer is implementing a pair of Cisco Nexus 9000 Series Switches. During the OSPF configuration, the engineer discovers unstable routing in the network. The investigation shows flapping routes after the new switches were introduced. Which set of actions resolves the issue?
- A. Configure a new IP address on the Ethernet interface toward the OSPF neighbor. Clear the OSPF process.
- B. Configure a new IP address on the Ethernet interface toward the OSPF neighbor. Clear the OSPF neighbor.
- C. Configure a new OSPF priority on the Ethernet interface toward the OSPF neighbor. Clear the OSPF neighbor.
- D. Configure a new IP address on the Loopback interface for the OSPF process. Clear the OSPF process
Answer: B
NEW QUESTION # 57
......
Exam Passing Guarantee 300-615 Exam with Accurate Quastions: https://www.updatedumps.com/Cisco/300-615-updated-exam-dumps.html
Test Engine to Practice Test for 300-615 Valid and Updated Dumps: https://drive.google.com/open?id=10BsyHH9vkIFHP8sZ9ZbUeoL_SLHc_AaS